News wire services in 1920s used
multiplex equipment that met the definition, but the modem function was incidental to the multiplexing function, so they are not commonly included in the history of modems.
In 1943, IBM adapted this technology to their unit record equipment and were able to transmit punched cards at 25 bits/second.
[citation needed] Mass-produced modems in the United States began as part of the
SAGE air-defense system in 1958, connecting terminals at various airbases, radar sites, and command-and-control centers to the SAGE director centers scattered around the U.S. and
Canada. SAGE modems were described by AT&T's
Bell Labs as conforming to their newly published
Bell 101 dataset standard. While they ran on dedicated telephone lines, the devices at each end were no different from commercial acoustically coupled Bell 101, 110 baud modems.
In the summer of 1960, the name
Data-Phone was introduced to replace the earlier term
digital subset. The
202 Data-Phone was a
half-duplex asynchronous service that was marketed extensively in late 1960. In 1962, the
201A and
201B Data-Phones were introduced. They were synchronous modems using two-bit-per-baud
phase-shift keying (PSK). The 201A operated half-duplex at 2,000 bit/s over normal phone lines, while the 201B provided
full duplex 2,400 bit/s service on four-wire leased lines, the send and receive channels running on their own set of two wires each.
The famous
Bell 103A dataset standard was also introduced by Bell Labs in 1962. It provided full-duplex service at 300 baud over normal phone lines.
Frequency-shift keying was used with the call originator transmitting at 1,070 or 1,270
Hz and the answering modem transmitting at 2,025 or 2,225 Hz. The readily available 103A2 gave an important boost to the use of remote low-speed terminals such as the KSR33, the
ASR33, and the
IBM 2741. AT&T reduced modem costs by introducing the originate-only 113D and the answer-only 113B/C modems.
The Carterfone decision
The
Novation CAT acoustically coupled modem
For many years, the Bell System (
AT&T) maintained a monopoly on the use of its phone lines, allowing only Bell-supplied devices to be attached to its network. Before 1968, AT&T maintained a monopoly on what devices could be
electrically connected to its phone lines. This led to a market for 103A-compatible modems that were
mechanically connected to the phone, through the handset, known as
acoustically coupled modems. Particularly common models from the 1970s were the
Novation CAT and the
Anderson-Jacobson, spun off from an in-house project at Stanford Research Institute (now SRI International).
Hush-a-Phone v. FCC was a seminal ruling in
United States telecommunications law decided by the
DC Circuit Court of Appeals on November 8, 1956. The District Court found that it was within the FCC's authority to regulate the terms of use of AT&T's equipment. Subsequently, the FCC examiner found that as long as the device was not physically attached it would not threaten to degenerate the system. Later, in the
Carterfone decision of 1968, the FCC passed a rule setting stringent AT&T-designed tests for electronically coupling a device to the phone lines. AT&T's tests were complex, making electronically-coupled modems expensive, so acoustically-coupled modems remained common into the early 1980s.
In December 1972,
Vadic introduced the
VA3400. This device was remarkable because it provided full duplex operation at 1,200 bit/s over the dial network, using methods similar to those of the 103A in that it used different frequency bands for transmit and receive. In November 1976, AT&T introduced the 212A modem to compete with Vadic. It was similar in design to Vadic's model, but used the lower frequency set for transmission. It was also possible to use the 212A with a 103A modem at 300 bit/s. According to Vadic, the change in frequency assignments made the 212 intentionally incompatible with acoustic coupling, thereby locking out many potential modem manufacturers. In 1977, Vadic responded with the VA3467 triple modem, an answer-only modem sold to computer center operators that supported Vadic's 1,200-bit/s mode, AT&T's 212A mode, and 103A operation.
The Smartmodem and the rise of BBSes
The next major advance in modems was the
Smartmodem, introduced in 1981 by
Hayes Communications. The Smartmodem was an otherwise standard 103A 300-bit/s modem, but was attached to a small controller that let the computer send commands to it and enable it to operate the phone line. The command set included instructions for picking up and hanging up the phone, dialing numbers, and answering calls. The basic
Hayes command set remains the basis for computer control of most modern modems.
Prior to the Hayes Smartmodem, dial-up modems almost universally required a two-step process to activate a connection: first, the user had to manually dial the remote number on a standard phone handset, and then secondly, plug the handset into an acoustic coupler. Hardware add-ons, known simply as dialers, were used in special circumstances, and generally operated by emulating someone dialing a handset.
With the Smartmodem, the computer could dial the phone directly by sending the modem a command, thus eliminating the need for an associated phone instrument for dialing and the need for an acoustic coupler. The Smartmodem instead plugged directly into the phone line. This greatly simplified setup and operation. Terminal programs that maintained lists of phone numbers and sent the dialing commands became common.
The Smartmodem and its clones also aided the spread of
bulletin board systems (BBSs). Modems had previously been typically either the call-only, acoustically coupled models used on the client side, or the much more expensive, answer-only models used on the server side. The Smartmodem could operate in either mode depending on the commands sent from the computer. There was now a low-cost server-side modem on the market, and the BBSs flourished.
Almost all modern modems can interoperate with
fax machines. Digital faxes, introduced in the 1980s, are simply a particular
image format sent over a high-speed (commonly 14.4 kbit/s) modem. Software running on the host computer can convert any image into fax-format, which can then be sent using the modem. Such software was at one time an add-on, but since has become largely universal.
Softmodem (dumb modem)
A PCI Winmodem/softmodem (on the left) next to a traditional ISA modem (on the right). Notice the less complex circuitry of the modem on the left.
A
Winmodem or
softmodem is a stripped-down modem that replaces tasks traditionally handled in
hardware with
software. In this case the modem is a simple interface designed to create voltage variations on the telephone line and to sample the line voltage levels (
digital to analog and
analog to digital converters). Softmodems are cheaper than traditional modems, since they have fewer hardware components. One downside is that the software generating and interpreting the modem tones is not simple (as most of the protocols are complex), and the performance of the computer as a whole often suffers when it is being used. For online gaming this can be a real concern. Another problem is lack of portability such that non-
Windows operating systems (such as
Linux) often do not have an equivalent driver to operate the modem.
Narrow-band/phone-line dialup modems
A standard modem of today contains two functional parts: an analog section for generating the signals and operating the phone, and a digital section for setup and control. This functionality is often incorporated into a single chip nowadays, but the division remains in theory. In operation the modem can be in one of two modes,
data mode in which data is sent to and from the computer over the phone lines, and
command mode in which the modem listens to the data from the computer for commands, and carries them out. A typical session consists of powering up the modem (often inside the computer itself) which automatically assumes command mode, then sending it the command for dialing a number. After the connection is established to the remote modem, the modem automatically goes into data mode, and the user can send and receive data. When the user is finished, the
escape sequence, "+++" followed by a pause of about a second, may be sent to the modem to return it to command mode, then a command (e.g. "ATH") to hang up the phone is sent. Note that on many modem controllers it is possible to issue commands to disable the escape sequence so that it is not possible for data being exchanged to trigger the mode change inadvertently.
The commands themselves are typically from the
Hayes command set, although that term is somewhat misleading. The original Hayes commands were useful for 300 bit/s operation only, and then extended for their 1,200 bit/s modems. Faster speeds required new commands, leading to a proliferation of command sets in the early 1990s. Things became considerably more standardized in the second half of the 1990s, when most modems were built from one of a very small number of chipsets. We call this the Hayes command set even today, although it has three or four times the numbers of commands as the actual standard.
Increasing speeds (V.21, V.22, V.22bis)
A 2,400 bit/s modem for a laptop.
The 300 bit/s modems used
audio frequency-shift keying to send data. In this system the stream of 1s and 0s in computer data is translated into sounds which can be easily sent on the phone lines. In the Bell 103 system the
originating modem sends 0s by playing a 1,070 Hz tone, and 1s at 1,270 Hz, with the
answering modem putting its 0s on 2,025 Hz and 1s on 2,225 Hz. These frequencies were chosen carefully, they are in the range that suffer minimum distortion on the phone system, and also are not
harmonics of each other.
In the 1,200 bit/s and faster systems,
phase-shift keying was used. In this system the two tones for any one side of the connection are sent at the similar frequencies as in the 300 bit/s systems, but slightly out of phase. By comparing the phase of the two signals, 1s and 0s could be pulled back out, for instance if the signals were 90 degrees out of phase, this represented two digits,
1, 0, at 180 degrees it was
1, 1. In this way each cycle of the signal represents two digits instead of one. 1,200 bit/s modems were, in effect, 600 symbols per second modems (600 baud modems) with 2 bits per symbol.
Voiceband modems generally remained at 300 and 1,200 bit/s (
V.21 and
V.22) into the mid 1980s. A
V.22bis 2,400-bit/s system similar in concept to the 1,200-bit/s Bell 212 signalling was introduced in the U.S., and a slightly different one in Europe. By the late 1980s, most modems could support all of these standards and 2,400-bit/s operation was becoming common.
Increasing speeds (one-way proprietary standards)
Many other standards were also introduced for special purposes, commonly using a high-speed channel for receiving, and a lower-speed channel for sending. One typical example was used in the French
Minitel system, in which the user's terminals spent the majority of their time receiving information. The modem in the Minitel terminal thus operated at 1,200 bit/s for reception, and 75 bit/s for sending commands back to the
servers.
Three U.S. companies became famous for high-speed versions of the same concept.
Telebit introduced its
Trailblazer modem in 1984, which used a large number of 36 bit/s channels to send data one-way at rates up to 18,432 bit/s. A single additional channel in the reverse direction allowed the two modems to communicate how much data was waiting at either end of the link, and the modems could change direction
on the fly. The Trailblazer modems also supported a feature that allowed them to spoof the
UUCP g protocol, commonly used on
Unix systems to send
e-mail, and thereby speed UUCP up by a tremendous amount. Trailblazers thus became extremely common on Unix systems, and maintained their dominance in this market well into the 1990s.
U.S. Robotics (USR) introduced a similar system, known as
HST, although this supplied only 9,600 bit/s (in early versions at least) and provided for a larger backchannel. Rather than offer spoofing, USR instead created a large market among
Fidonet users by offering its modems to BBS
sysops at a much lower price, resulting in sales to end users who wanted faster file transfers. Hayes was forced to compete, and introduced its own 9,600-bit/s standard,
Express 96 (also known as
Ping-Pong), which was generally similar to Telebit's PEP. Hayes, however, offered neither protocol spoofing nor sysop discounts, and its high-speed
4,800 and 9,600 bit/s (V.27ter, V.32)
Echo cancellation was the next major advance in modem design. Local telephone lines use the same wires to send and receive, which results in a small amount of the outgoing signal bouncing back. This signal can confuse the modem, which was unable to distinguish between the echo and the signal from the remote modem. This was why earlier modems split the signal frequencies into 'answer' and 'originate'; the modem could then ignore its own transmitting frequencies. Even with improvements to the phone system allowing higher speeds, this splitting of available phone signal
bandwidth still imposed a half-speed limit on modems.
Echo cancellation got around this problem. Measuring the echo delays and magnitudes allowed the modem to tell if the received signal was from itself or the remote modem, and create an equal and opposite signal to cancel its own. Modems were then able to send over the whole frequency spectrum in both directions at the same time, leading to the development of 4,800 and 9,600 bit/s modems.
Increases in speed have used increasingly complicated communications theory. 1,200 and 2,400 bit/s modems used the phase shift key (PSK) concept. This could transmit two or three bits per symbol. The next major advance encoded four bits into a combination of amplitude and phase, known as
Quadrature Amplitude Modulation (QAM). Best visualized as a
constellation diagram, the bits are mapped onto points on a graph with the x (real) and y (quadrature) coordinates transmitted over a single carrier.
The new V.27ter and V.32 standards were able to transmit 4 bits per symbol, at a rate of 1,200 or 2,400 baud, giving an effective bit rate of 4,800 or 9,600 bit/s. The carrier frequency was 1,650 Hz. For many years, most engineers considered this rate to be the limit of data communications over telephone networks.
Error correction and compression
Operations at these speeds pushed the limits of the phone lines, resulting in high error rates. This led to the introduction of
error-correction systems built into the modems, made most famous with
Microcom's
MNP systems. A string of MNP standards came out in the 1980s, each increasing the effective data rate by minimizing overhead, from about 75% theoretical maximum in MNP 1, to 95% in MNP 4. The new method called MNP 5 took this a step further, adding
data compression to the system, thereby increasing the data rate above the modem's rating. Generally the user could expect an MNP5 modem to transfer at about 130% the normal data rate of the modem. Details of MNP were later released and became popular on a series of 2,400-bit/s modems, and ultimately led to the development of
V.42 and
V.42bis ITU standards. V.42 and V.42bis were non-compatible with MNP but were similar in concept: Error correction and compression.
Another common feature of these high-speed modems was the concept of
fallback, or
speed hunting, allowing them to talk to less-capable modems. During the call initiation the modem would play a series of signals into the line and wait for the remote modem to respond to them. They would start at high speeds and progressively get slower and slower until they heard an answer. Thus, two USR modems would be able to connect at 9,600 bit/s, but, when a user with a 2,400-bit/s modem called in, the USR would fallback to the common 2,400-bit/s speed. This would also happen if a V.32 modem and a HST modem were connected. Because they used a different standard at 9,600 bit/s, they would fall back to their highest commonly supported standard at 2,400 bit/s. The same applies to V.32bis and 14,400 bit/s HST modem, which would still be able to communicate with each other at only 2,400 bit/s.
Breaking the 9.6k barrier
In 1980,
Gottfried Ungerboeck from
IBM Zurich Research Laboratory applied powerful
channel coding techniques to search for new ways to increase the speed of modems. His results were astonishing but only conveyed to a few colleagues
[1]. Finally in 1982, he agreed to publish what is now a landmark paper in the theory of information coding.
[citation needed] By applying powerful parity check coding to the bits in each symbol, and mapping the encoded bits into a two-dimensional diamond pattern, Ungerboeck showed that it was possible to increase the speed by a factor of two with the same error rate. The new technique was called
mapping by set partitions (now known as
trellis modulation).
Error correcting codes, which encode code words (sets of bits) in such a way that they are far from each other, so that in case of error they are still closest to the original word (and not confused with another) can be thought of as analogous to
sphere packing or packing pennies on a surface: the further two bit sequences are from one another, the easier it is to correct minor errors.
V.32bis was so successful that the older high-speed standards had little to recommend them. USR fought back with a 16,800 bit/s version of HST, while AT&T introduced a one-off 19,200 bit/s method they referred to as V.32ter (also known as V.32 terbo or tertiary), but neither non-standard modem sold well.
[edit] V.34/28.8k and 33.6k
An ISA modem manufactured to conform to the V.34 protocol.
Any interest in these systems was destroyed during the lengthy introduction of the 28,800 bit/s
V.34 standard. While waiting, several companies decided to release hardware and introduced modems they referred to as
V.FAST. In order to guarantee compatibility with V.34 modems once the standard was ratified (1994), the manufacturers were forced to use more flexible parts, generally a
DSP and
microcontroller, as opposed to purpose-designed
ASIC modem chips.
Today, the ITU standard V.34 represents the culmination of the joint efforts. It employs the most powerful coding techniques including channel encoding and shape encoding. From the mere 4 bits per symbol (9.6 kbit/s), the new standards used the functional equivalent of 6 to 10 bits per symbol, plus increasing baud rates from 2,400 to 3,429, to create 14.4, 28.8, and 33.6 kbit/s modems. This rate is near the theoretical
Shannon limit. When calculated, the Shannon capacity of a narrowband line is
, with
the (linear) signal-to-noise ratio. Narrowband phone lines have a bandwidth from 300-4000 Hz, so using
(SNR = 30dB): capacity is approximately 35 kbit/s.
Without the discovery and eventual application of trellis modulation, maximum telephone rates using voice-bandwidth channels would have been limited to 3,429 baud * 4 bit/symbol == approximately 14 kbit/s using traditional QAM. (DSL makes use of the bandwidth of traditional copper-wire twisted pairs between subscriber and the central office, which far exceeds that of analog voice circuitry.)
V.61/V.70 Analog/Digital Simultaneous Voice and Data
The V.61 Standard introduced Analog Simultaneous Voice and Data (ASVD). This technology allowed users of v.61 modems to engage in point-to-point voice conversations with each other while their respective modems communicated.
In 1995, the first DSVD (Digital Simultaneous Voice and Data) modems became available to consumers, and the standard was ratified as v.70 by the International Telecommunication Union (ITU) in 1996.
Two DSVD modems can establish a completely digital link between each other over standard phone lines. Sometimes referred to as "the poor man's ISDN," and employing a similar technology, v.70 compatible modems allow for a maximum speed of 33.6 kbps between peers. By using a majority of the bandwidth for data and reserving part for voice transmission, DSVD modems allow users to pick up a telephone handset interfaced with the modem, and initiate a call to the other peer.
One practical use for this technology was realized by early two player video gamers, who could hold voice communication with each other while in game over the PSTN.
Advocates of DSVD envisioned whiteboard sharing and other practical applications for the standard, however, with advent of cheaper 56kbps analog modems intended for Internet connectivity, peer-to-peer data transmission over the PSTN became quickly irrelevant. Also, the standard was never expanded to allow for the making or receiving of arbitrary phone calls while the modem was in use, due to the cost of infrastructure upgrades to telephone companies, and the advent of ISDN and DSL technologies which effectively accomplished the same goal.
Today, Multi-Tech is the only known company to continue to support a v.70 compatible modem. While their device also offers v.92 at 56kbps, it remains significantly more expensive than comparable modems sans v.70 support.
Using digital lines and PCM (V.90/92)
In the late 1990s Rockwell/Lucent and U.S. Robotics
introduced new competing technologies based upon the digital transmission used in modern telephony networks. The standard digital transmission in modern networks is 64 kbit/s but some networks use a part of the bandwidth for remote office signaling (e.g., to hang up the phone), limiting the effective rate to 56 kbit/s
DS0. This new technology was adopted into ITU standards V.90 and is common in modern computers. The 56 kbit/s rate is only possible from the central office to the user site (downlink). In the United States, government regulation limits the maximum power output, resulting in a maximum data rate of 53.3 kbit/s. The uplink (from the user to the central office) still uses V.34 technology at 33.6 kbit/s.
Later in
V.92, the digital
PCM technique was applied to increase the upload speed to a maximum of 48 kbit/s, but at the expense of download rates. For example a 48 kbit/s upstream rate would reduce the downstream as low as 40 kbit/s, due to echo on the telephone line. To avoid this problem, V.92 modems offer the option to turn off the digital upstream and instead use a 33.6 kbit/s analog connection, in order to maintain a high digital downstream of 50 kbit/s or higher.
[2] V.92 also adds two other features. The first is the ability for users who have call waiting to put their
dial-up Internet connection on hold for extended periods of time while they answer a call. The second feature is the ability to quickly connect to one's ISP. This is achieved by remembering the analog and digital characteristics of the telephone line, and using this saved information to reconnect at a fast pace.
Using compression to exceed 56k
Today's
V.42,
V.42bis and
V.44 standards allow the modem to transmit data faster than its basic rate would imply. For instance, a 53.3 kbit/s connection with V.44 can transmit up to 53.3*6 == 320 kbit/s using pure text. However, the compression ratio tends to vary due to noise on the line, or due to the transfer of already-compressed files (ZIP files, JPEG images, MP3 audio, MPEG video).
[3] At some points the modem will be sending compressed files at approximately 50 kbit/s, uncompressed files at 160 kbit/s, and pure text at 320 kbit/s, or any value in between.
[4]In such situations a small amount of memory in the modem, a buffer, is used to hold the data while it is being compressed and sent across the phone line, but in order to prevent overflow of the buffer, it sometimes becomes necessary to tell the computer to pause the datastream. This is accomplished through hardware flow control using extra lines on the modem–computer connection. The computer is then set to supply the modem at some higher rate, such as 320 kbit/s, and the modem will tell the computer when to start or stop sending data.
Compression by the ISP
As telephone-based 56k modems began losing popularity, some Internet service providers such as Netzero and Juno started using pre-compression to increase the throughput and maintain their customer base. As example, the
Netscape ISP uses a compression program that squeezes images, text, and other objects at the modem server, just prior to sending them across the phone line. Certain content using lossy compression (e.g., images) may be recompressed (transcoded) using different parameters to the compression algorithm, making the transmitted content smaller but of lower quality. The server-side compression operates much more efficiently than the on-the-fly compression of V.44-enabled modems due to the fact that V.44 is a generalized compression algorithm whereas other compression techniques are application-specific (JPEG, MPEG, Vorbis, etc.). Typically Website text is compacted to 4% thus increasing effective throughput to approximately 1,300 kbit/s. The accelerator also pre-compresses Flash executables and images to approximately 30% and 12%, respectively.
The drawback of this approach is a loss in quality, where the GIF and JPEG images are lossy compressed, which causes the content to become pixelated and smeared. However the speed is dramatically improved such that Web pages load in less than 5 seconds, and the user can manually choose to view the uncompressed images at any time. The ISPs employing this approach advertise it as "surf 5× faster" or simply "accelerated dial-up".
[5][6]
List of dialup speeds
Note that the values given are maximum values, and actual values may be slower under certain conditions (for example, noisy phone lines).
[7] For a complete list see the companion article
list of device bandwidths. A
baud is one symbol per second; each symbol may encode one or more data bits.
| Connection | Bitrate (kbit/s) | Year Released |
| 110 baud Bell 101 modem | 0.1 | 1958 |
| 300 baud (Bell 103 or V.21) | 0.3 | 1962 |
| 1200 modem (1200 baud) (Bell 202) | 1.2 |
|
| 1200 Modem (600 baud) (Bell 212A or V.22) | 1.2 |
|
| 2400 Modem (600 baud) (V.22bis) | 2.4 |
|
| 2400 Modem (1200 baud) (V.26bis) | 2.4 |
|
| 4800 Modem (1600 baud) (V.27ter) | 4.8 |
|
| 9600 Modem (2400 baud) (V.32) | 9.6 |
|
| 14.4k Modem (2400 baud) (V.32bis) | 14.4 |
|
| 28.8k Modem (3200 baud) (V.34) | 28.8 |
|
| 33.6k Modem (3429 baud) (V.34) | 33.6 |
|
| 56k Modem (8000/3429 baud) (V.90) | 56.0/33.6 |
|
| 56k Modem (8000/8000 baud) (V.92) | 56.0/48.0 |
|
| Bonding modem (two 56k modems)) (V.92)[8] | 112.0/96.0 |
|
| Hardware compression (variable) (V.90/V.42bis) | 56.0-220.0 |
|
| Hardware compression (variable) (V.92/V.44) | 56.0-320.0 |
|
| Server-side web compression (variable) (Netscape ISP) | 100.0-1,000.0 |
|
Radio modems
Direct broadcast satellite,
WiFi, and
mobile phones all use modems to communicate, as do most other wireless services today. Modern telecommunications and data networks also make extensive use of
radio modems where long distance data links are required. Such systems are an important part of the
PSTN, and are also in common use for high-speed
computer network links to outlying areas where fibre is not economical.
Even where a cable is installed, it is often possible to get better performance or make other parts of the system simpler by using radio frequencies and modulation techniques through a cable.
Coaxial cable has a very large bandwidth, however signal attenuation becomes a major problem at high data rates if a digital signal is used. By using a modem, a much larger amount of digital data can be transmitted through a single piece of wire. Digital cable television and cable Internet services use radio frequency modems to provide the increasing bandwidth needs of modern households. Using a modem also allows for
frequency-division multiple access to be used, making full-duplex digital communication with many users possible using a single wire.
Wireless modems come in a variety of types, bandwidths, and speeds. Wireless modems are often referred to as transparent or smart. They transmit information that is modulated onto a carrier frequency to allow many simultaneous wireless communication links to work simultaneously on different frequencies.
Transparent modems operate in a manner similar to their phone line modem cousins. Typically, they were
half duplex, meaning that they could not send and receive data at the same time. Typically transparent modems are polled in a round robin manner to collect small amounts of data from scattered locations that do not have easy access to wired infrastructure. Transparent modems are most commonly used by utility companies for data collection.
Smart modems come with a media access controller inside which prevents random data from colliding and resends data that is not correctly received. Smart modems typically require more bandwidth than transparent modems, and typically achieve higher data rates. The IEEE
802.11 standard defines a short range modulation scheme that is used on a large scale throughout the world.
WiFi and WiMax
Mobile modems and routers
Modems which use a mobile telephone system (
GPRS,
UMTS,
HSPA,
EVDO,
WiMax, etc.), are known as
wireless modems (sometimes also called cellular modems). Wireless modems can be embedded inside a laptop or appliance or external to it. External wireless modems are
connect cards,
usb modems for
mobile broadband and
cellular routers. A
connect card is a
PC card or
ExpressCard which slides into a
PCMCIA/PC card/ExpressCard slot on a computer.
USB wireless modems use a USB port on the laptop instead of a PC card or ExpressCard slot. A cellular router may have an external datacard (
AirCard) that slides into it. Most cellular routers do allow such datacards or USB modems. Cellular Routers may not be modems per se, but they contain modems or allow modems to be slid into them. The difference between a cellular router and a wireless modem is that a cellular router normally allows multiple people to connect to it (since it can route, or support multipoint to multipoint connections), while the modem is made for one connection.
Most of the
GSM wireless modems come with an integrated
SIM cardholder (i.e.,
Huawei E220, Sierra 881, etc.) and some models are also provided with a microSD memory slot and/or jack for additional external antenna such as Huawei E1762 and Sierra Wireless Compass 885.
[9][10] The CDMA (EVDO) versions do not use
R-UIM cards, but use
Electronic Serial Number (ESN) instead.
The cost of using a wireless modem varies from country to country. Some carriers implement flat rate plans for unlimited data transfers. Some have caps (or maximum limits) on the amount of data that can be transferred per month. Other countries have plans that charge a fixed rate per data transferred—per megabyte or even kilobyte of data downloaded; this tends to add up quickly in today's content-filled world, which is why many people are pushing for
flat data rates.
The faster data rates of the newest wireless modem technologies (UMTS, HSPA, EVDO, WiMax) are also considered to be broadband wireless modems and compete with other broadband modems below.
Broadband
Cable modems use a range of frequencies originally intended to carry RF television channels. Multiple cable modems attached to a single cable can use the same frequency band, using a low-level media access protocol to allow them to work together within the same channel. Typically, 'up' and 'down' signals are kept separate using
frequency division multiple access.
Broadband modems should still be classed as modems, since they use complex waveforms to carry digital data. They are more advanced devices than traditional
dial-up modems as they are capable of modulating/demodulating hundreds of channels simultaneously.
When broadband technology was introduced, networking and routers were unfamiliar to consumers. However, many people knew what a modem was as most internet access was through dial-up. Due to this familiarity, companies started selling broadband modems using the familiar term modem rather than vaguer ones like adapter or transceiver, or even "bridge".
Many broadband modems must be configured in
bridge mode before they can use a router.
Home networking
Although the name
modem is seldom used in this case, modems are also used for high-speed home networking applications, specially those using existing home wiring. One example is the
G.hn standard, developed by
ITU-T, which provides a high-speed (up to 1 Gbit/s)
Local area network using existing home wiring (
power lines, phone lines and
coaxial cables). G.hn devices use
orthogonal frequency-division multiplexing (OFDM) to modulate a digital signal for transmission over the wire.
The phrase "
Null modem" was used to describe attaching a specially wired cable between the
serial ports of two personal computers. Basically, the transmit output of one computer was wired to the receive input of the other; this was true for both computers. The same software used with modems (such as Procomm or Minicom) could be used with the null modem connection.
Deep-space telecommunications
Differences between deep space telecom modems and landline modems:
- digital modulation formats that have high doppler immunity are typically used
- waveform complexity tends to be low, typically binary phase shift keying
- error correction varies mission to mission, but is typically much stronger than most landline modems
Voice modem
